Bulk material balers-wrappers LT-Master

For pressing corn, crushed grains, sugar pomace and many other bulk products into rolls

For consultation or to receive a purchase offer, please contact the following contacts:

LT-MASTER – a combination of three devices consisting of a feeder/dosing device, a round baler and a wrapper.

High quality and efficient work

Crushed corn, crushed grains, sugar beet slices/cake, and various herbs are pressed into rolls.
The feed remains of exceptional quality all year round, fresh, and suitable for use in both winter and summer.
Extremely fast air removal, ideal preservation, no risk of secondary fermentation or heating.
Ideally clean production work, completely uncontaminated feed.
Rolls are very convenient for daily animal feeding - feed is delivered quickly and easily.
The size of one roll is from 0.6 to 1.15 mx 1.20 m, weight up to 1100 kg.

LT Master advantages

More rolls per hour. The ideally coordinated workflow ensures high throughput – up to 60 tons per hour.

Automated management. The PROFI control program controls the entire workflow fully automatically.

Fast and agile. The mobile rotating drawbar allows the machine to be turned 30° in both directions. This ensures a minimum turning angle and allows the machine to be coupled to the tractor on both the left and right sides.

Central lubrication. The central lubricator continuously supplies grease and/or oil to the most important lubrication points, ensuring an extremely long service life and minimal wear.

No path is far. The 80 km/h chassis allows you to quickly reach any job site, whether you are traveling by tractor or truck. (with the 80 km/h chassis, a dual-circuit pneumatic brake system is required)

Feeder/dosing device

Low profile design – very convenient loading of crushed mass.

Dosing rollers and feed screws. The even profile rollers guarantee ideal material distribution on the flat conveyor.

High capacity feeder prevents the LT-Master from stopping when changing the dump truck.

Dosing deviceThe speed of the scraper bottom automatically adjusts and regulates the amount of material.

Scraper bottom chains. Galvanized forged scraper bottom chains on the discount conveyor and feeder are extremely durable.

Baler

Extremely high compression density. The continuous belt constantly exerts strong pressure on the material. A roll with a diameter of 1.15 m weighs about 1000 kg!

Longevity. Large bearings with a perfectly matched lubrication system ensure that the press will operate for a very long time.

Camera with fixed roller. The two parts of the chamber are surrounded by a continuous belt, which reduces breakage losses. The belt tension can be adjusted hydraulically.

Mesh and film. An efficient binding system that ensures the best feed quality while saving time and money.

Refeed belt moves along the entire length of the lower part of the machine and prevents breakage losses by catching all debris and returning it uncontaminated to the lower conveyor.

Winder

Mobile wrapping table moves under the press and picks up the roll directly, quickly and carefully.

Double wrapping handle and two 750 mm film tensioners. 2 sensors reliably monitor the film and react quickly when the film runs out or tears.

Monitoring of single film roll mode. When the film runs out or tears, the wrapping table feed speed is reduced until an overlap of 50 % is again ensured. This completes the roll wrapping process without any interruptions.

The roller ramp folds hydraulically – ensures smooth roll lowering.

Automatic film cutting and storage system. The stainless steel gravity knife cuts the film precisely. The standard floating film knife position ensures that the film peels off easily and leaves no residue.

	LT-Master GOWEIL
Weight, kg	15200
Roll diameter, m	1.15

TRANSPORTATION POSITION
Length, mm	11550
Width, mm	2550
Height, mm	4000

WORKING SITUATION
Length, mm	13940
Width, mm	5200
Height, mm	4010

Over the past few decades, since 1988, GOWEIL has established itself in the market as a specialist in the production of hay bale wrappers. Since the company GOWEIL Maschinenbau GmbH exports the majority of its production – the 86% – and the machines are known and widely used all over the world. All machines and equipment are designed, developed and manufactured exclusively at the company's headquarters in Kirchschlag (Upper Austria).

All GOWEIL The products reflect the latest technologies and are designed to meet the individual needs of farms.