3–10-meter mounted cultivators are designed for soil preparation after plowing
Compact PS – a time-tested seed drill with a working width of 3–10 meters, which prepares the soil for sowing after plowing in a single pass
- Working width from 3 to 9,85 metres.
- Suitable for use with from 165 hp power technology.
- Forks planted in two rows, with a spacing of 21.5–25.5 cm between the rows and 24–49 cm between the rows.
- Working depth of the tines from 0 to 10 cm.
Key Features of the Farmet Kompaktomat PS
Proper preparation of the seedbed
The Kompaktomat PS can perform up to 9 different soil preparation operations in a single pass. Several working sections break up clods, level the surface, loosen, and compact the soil, thereby creating a uniform seedbed throughout the entire working depth.
Modular configurations for various soil types
The Kompaktomat PS can be equipped with various tine, Flexi-board levelling board, and roller options, allowing the implement to be precisely adapted to different soil types and farming practices. The wide range of configuration options allows every farm to configure the optimal seed drill according to its needs and working conditions.
Optimal soil compaction
Properly distributed implement weight and consistent soil cultivation help restore optimal soil structure. A well-compacted seedbed retains moisture better, ensures better seed-to-soil contact, and promotes more uniform crop emergence.
3-year warranty
All Farmet equipment comes with a 3-year warranty. The company pays particular attention to the high quality and reliability of its machinery. This commitment reflects the company's long-standing philosophy based on precision machining, durability and long service life.
Working areas
Compact PS
Compactor PS LONG
- The area where the tractor tracks are being loosened. Precise tillage ensures uniform crop germination.
- Primary soil levelling zone. A carefully leveled soil surface ensures uniform further compaction and soil cultivation.
- Area of soil compaction caused by the front roller. The front roller breaks up clods on the soil surface, while also compacting the soil and restoring its capillary action.
- Seedbed preparation zone. The coulter section loosens the soil to the set depth. This depth should correspond to the depth of the upcoming sowing. The coulters with arrow-shaped points ensure thorough surface tillage and weed control.
- Furrow levelling zone behind the coulter section.
- Soil compaction zone using a rear roller. The roller finely breaks up clods and ensures final soil compaction, fully restoring its capillary action. Intense capillary movement of water to the surface ensures good plant germination even during dry periods.
- Final soil leveling area. The rear levelling board ensures perfect soil levelling for subsequent sowing.
High quality and efficient work
- Underway 7 operations at the same time.
- Large working speed – up to 14 km/h.
- Creates proper soil structure and compacts it, ensuring even cultivation.
- Precise setting of the working depth of the coulters ensures very good seedbed preparation.
- Automatic tine protection guarantees uninterrupted operation.
- Excellent leveling of uneven terrain.
- A reliable germinator for your farm work with optimal soil compaction.
In one pass, the soil is processed to a condition suitable for sowing, and the main advantages of the machine are: excellent surface smoothing, fine crushing of lumps and formation of well-compacted soil for sowing. Up to 9 operations in one pass. Suitable for more intensive soil cultivation after ploughing, when the amount of crop residues is minimal.
Greater permeability of plant residues. Suitable for soil cultivation after loosening, when there is a lot of crushed plant residues on the surface.
The germinator controls are designed to ensure maximum worker safety. Simple but high-quality construction with minimal maintenance requirements. Poor cultivation With uneven soil cultivation, there is a risk that plants will germinate incorrectly and unevenly. Quality cultivation Uniform soil cultivation using the Kompaktomat germinator results in uniform plant germination.
Extremely durable materials Extremely durable, high-quality materials used for the production of working parts ensure a long service life. Robust frame construction. Solid frontno ironing section Ensures high-quality soil surface leveling. Tine protection Automatic tine protection.
Minimal number of adjustable and lubricated points, so maintenance is extremely easy.
Front ironing section Height adjustment of the front ironing section. Hydraulic control of the front leveling section The position of the front screed section can be continuously adjusted during operation, depending on the prevailing conditions. Can also be fitted to older models. Deflector behind the loosening section A sturdy deflector for better crop residue throughput is an optional extra. Leveling section behind the loosening section Height adjustment of the leveling section located behind the loosening section. Working depth Setting the working depth of the plows. Hydraulic working depth adjustment The working depth of the loosening section can be conveniently adjusted hydraulically directly from the tractor cabin. Can also be fitted to older models.
One of the biggest advantages is versatility and adaptability, providing great work versatility. Folding into transport position
Standard plowshare DURA+ plowshare MULTICARBIDE plowshare
View the differences in each section Optional equipment Section AL Section CF Section AP Section AL4
The trailed Kompaktomat K 300 P – K 1000 PS germinators can be combined with other units and machines. Additionally, a rear three-point category 2 hitch must be selected. Combination with additional compaction rollers All you need is a three-point hitch. Combination with additional compaction rollers Combination with a seed drill Hydraulic connections for the pneumatic seed drill fan and a hydraulic connection for controlling the seed drill marker must be selected.
Compactor K 800 PS
Compactor K 800 PS LONG
Excellent surface smoothing, clod breaking
Post-ploughing configurations
Configurations for work after loosening
Minimum maintenance requirements
Excellent compaction → ensures water absorption and capillary rise of water to the surface
Sturdy construction
Easy to use
A cleverly designed machine
Choosing Among Different Types of Plows
Tine sections
Combination with other units
Examples of Kompaktomat PS germinator configurations
Kompaktomat Standard Beam Plow Designed for AL / AP sections and CA wheel mark eradicators. Kompaktomat boom tine DURA+ Designed for AL / AP sections and CA wheel mark eradicators. Kompaktomat MULTICARBIDE plow blade Designed for AL / AP sections and CA wheel mark eradicators. Kompaktomat boom tine DURA+ Designed for AL4 section. CARBIDE chisel For the CF section. Double-sided chisel For the CF section. Double-ended standard chisel Designed for CC track looseners. DURA+ Double-Sided Chisel Designed for CC track looseners.
AP section Universal tillage section with 27 cm wide tine arms arranged in two rows. The tines are mounted on tine holders with a geometry that improves the throughput of crop residues. This tine section is suitable for fields with a lot of chopped crop residues, as well as for heavy soils. Comes standard with a height-adjustable levelling beam behind the tines. AL section The section consists of 27 cm wide tine coulters arranged in two rows. This section is suitable for light soils without plant residues. It comes standard with a height-adjustable levelling bar behind the coulters. AL4 section (suitable for Kompaktomat LONG) The section consists of 15 cm wide tine arms arranged in four rows. This section is suitable for light, medium and heavy soils. It is equipped with a height-adjustable levelling beam behind the tines as standard. CF section The section consists of narrow tines 3.5 cm wide, arranged in four rows. Ideal for spring soil preparation or heavy soils where bringing moist soil to the surface is undesirable. Comes standard with a levelling bar behind the tines.
Crosskill roller CR Diameter – 400 mm Can only be used as a rear roller. Beam roller BR Diameter – 400 mm Can be used as a front and rear roller. Spiral beam roller SB Diameter – 400 mm Can be used as a front and rear roller. Ring roller RR Diameter – 400 mm Can be used as a front and rear roller. Double Crosskill roller DCR Diameter – 400 mm Can only be used as a rear roller. Double Crosskill Roller DCRL Diameter – 400 mm Can only be used as a rear roller. Two Crosskill rollers CR + CR Diameter – 400 mm Can only be used as a rear roller. Spiral beam roller SB + Crosskill roller CR Diameter – 400 mm High-quality clod breaking. Suitable for working in wet conditions. SB Spiral Beam Roller + SB Spiral Beam Roller Diameter – 400 mm Can be used as a front and rear roller. The correct selection of the rear roller type, which significantly contributes to the final quality of cultivation, is of utmost importance. The soil is repeatedly compacted by the roller, while at the same time breaking up clods and leveling the surface. The type of roller is selected taking into account the type of soil and the planned use of the machine.
Track scarifiers CA Automatically releasing tractor wheel mark eradicators with a tine arm. Suitable for light soils where there is no risk of raising wet clods to the surface. Track cultivators with double-sided tines CC Automatic release tractor wheel mark eradicators with double-sided tines. Suitable for heavy soils where there is a risk of raising wet clods to the surface.
Fixed ironing section Automatically releasing levelling beam with toothed profile. Robust construction ensuring precise levelling of large clods. FL = fixed mechanical slide, FH = fixed hydraulic slide. Flexi-board ironing board Automatically unprotected levelling beam, consisting of individual flexible segments. Better clod breaking. L = Flexi-board, FB = hydraulically operated Flexi-board. Joining the edges of Flexi-board ironing boards with stabilization The arms of the ironing board function as a single unit, ensuring greater stability. Additional leveling section mounted behind the front roller FRL Designed for the Kompaktomat LONG model. Automatic leveling section with the possibility of setting the lower position. The leveling section ensures more intensive mixing, resulting in a finer soil structure.
Mechanically controlled Flexi-board ironing board
Rear leveling beam Passive soil levelling behind the rear roller. The aggressiveness of the levelling strip is adjusted by means of rotary stops. Can be used with all types of rear rollers. Crosskill roller RFC Active crushing of remaining clods behind the rear roller. Can be used with all types of rollers in the Kompaktomat LONG model. Cannot be used behind the rear double-row rollers in the Kompaktomat PS model. Rod roller RF Active crushing of remaining clods behind the rear roller.
Rear suspension TPH cat. 2 and 3 The trailed Kompaktomat germinators can be equipped with a rear linkage for aggregation with other equipment. The rear linkage is a two-hose hydraulic system for folding additional equipment. Hydraulic connection for controlling the drill marker Possibility of additionally installing a single or dual-hose hydraulic system to control the drill markers on the Kompaktomat germinator with rear TPS suspension. Hydraulic connections for the drill fan Hydraulic connections for the pneumatic seed drill fan can be optionally available together with the rear TPH suspension.
TPH hitch T2, T3, T4 – aggregation into rear suspension arms. T2 – connection pins Ø 28 mm Lower hitch eye C40, C50, C70 – maximum vertical load – 3000 kg. C40 – connection pin Ø 40 mm K80 coupling Ø 80 mm Maximum vertical load – 3000 kg. K80 – towbar 80 mm
Electro-hydraulic flow distributor Divides one tractor hydraulic circuit into three separate circuits. Dual-line single-circuit pneumatic brakes Hydraulic brakes
Working tools
Tine sections
AL AL-L CF CF-L AP AP-L AL4
Number of tine rows, pcs. /
distance between rows, mm2 / 400 2 / 510 4 / 240 4 / 265 2 / 490 2 / 600 4 / 270
Leveling beam behind the tines ●●●● ●●●● ●●●● ●●●● ●●●● ●●●● ●●●●
Full surface cultivation ●●●● ●●●● ●●○○ ●●○○ ●●●● ●●●● ●●●●
Suitability for light soils ●●●● ●●●● ●●●● ●●●● ●●●● ●●●● ●●●●
Suitability for medium soils ●●●○ ●●●○ ●●●○ ●●●○ ●●●● ●●●● ●●●●
Suitability for heavy soils ●●●○ ●●●○ ●●●○ ●●●○ ●●●● ●●●● ●●●●
Suitability for rocky soils ●●●○ ●●●○ ●●●○ ●●●○ ●●●● ●●●● ●●●○
Suitability for wet soils ●●○○ ●●○○ ●●●● ●●●● ●●○○ ●●○○ ●●●○
Resistance to clogging ●●○○ ●●○○ ●●●○ ●●●○ ●●●○ ●●●○ ●●●○
Rollers
Weight – 133 kg/m
Excellent work in light, medium and heavy soils, high-quality compaction and clod breaking.
Weight – 63 kg/m
Good clod breaking. Not very suitable for wet conditions.
Weight – 70 kg/m
High-quality clod breaking. Suitable for use in wet conditions.
Weight – 115 kg/m
It works well in all types of soils, maintains good working depth, and is suitable even for wetter soils.
Weight – 185 kg/m
Distance between roller rows – 274 mm
Excellent work in light, medium and heavy soils, high-quality compaction and clod breaking. Compared to the Crosskill roller, it ensures more intensive clod breaking.
Weight – 185 kg/m
Distance between roller rows – 505 mm
Excellent work in light, medium and heavy soils, high-quality compaction and clod breaking. Compared to the Crosskill roller, it ensures more intensive clod breaking.
Weight – 265 kg/m
Distance between roller rows – 505 mm
Excellent work in light, medium and heavy soils, high-quality compaction and clod breaking.
Weight – 203 kg/m
Distance between roller rows – 505 mm
Weight – 140 kg/m
Distance between roller rows – 505 mm
High-quality clod breaking. Suitable for use in wet conditions.
Crosskill roller CR Beam roller BR Spiral beam roller SB Ring roller RR Double Crosskill roller DCR Double Crosskill Roller DCRL Two Crosskill rollers CR + CR Spiral beam roller SB + Crosskill roller CR
Crushing ●●●● ●●●○ ●●●○ ●●○○ ●●●● ●●○○ ●●●● ●●●●
Compaction ●●●● ●●●○ ●●●○ ●●●● ●●●● ●●●● ●●●● ●●●●
Depth support ●○○○ ●●●○ ●●●○ ●●●● ●●○○ ●●○○ ●●○○ ●●●○
Resistance to clogging ●●●○ ●●○○ ●●●○ ●●●● ●●●● ●●●○ ●●●○ ●●○○
Suitability for rocky soils ●●○○ ●●●○ ●●●○ ●●●○ ●●○○ ●●●● ●●○○ ●●○○
Suitability for wet soils ●●○○ ●○○○ ●●●○ ●●●● ●●●○ ●●○○ ●●○○ ●○○○
Suitability for heavy soils ●●●○ ●●○○ ●●○○ ●●●○ ●●●● ●●●● ●●●○ ●●○○
Suitability for medium soils ●●●● ●●●○ ●●●○ ●●●○ ●●●● ●●●● ●●●● ●●●○
Suitability for light soils ●●●● ●●●● ●●●● ●●●○ ●●●● ●●●● ●●●● ●●●●
Track looseners
Ironing sections
Rear sections
Rear hitch – for attachment to other machines
Towing
T3 – connection pins Ø 36 mm
T4 – connection pins Ø 50 mm
C50 – connecting pin Ø 50 mm
C70 – connection pin Ø 70 mm
Other optional equipment
KOMPAKTOMAT models without brakes
KOMPAKTOMAT models with brakes
COMPACTOMAT LONG
K 300 P K 400 PS K 450 PS K 500 PS K 600 PS
Working width, mm 3 000 4 000 4 500 5 000 6 000
Transport width, mm 3 000 3 000 3 000 3 000 3 000
Transport height, mm 1 650 2 670 3 030 2 790 3 230
Total length, mm 5 965 5 965 5 965 6 105 6 105
Working depth, mm 0-100 0-100 0–100 0-100 0-100
Arrow tines – AL section, pcs. 13 18 20 23 27
Forged tines – CF section, pcs. 30 39 47 49 59
Arrow tines – AP section, pcs. 12 16 20 23 24
Productivity, ha/hour 2,2 - 3,2 3-4 3,5 - 4,5 3-5 3,5 - 6
Tractor power, kW/HP 70 / 95 90 / 125 110 / 150 120 / 165 130 / 180
Working speed, km/h 10–14 10–14 10–14 10–14 10–14
Maximum working slope, ° 11 6 6 6 6
Tire measurements - for transportation 400/60-15,5 400/60-15,5 400/60-15,5 19,0/45-17 19,0/45-17
Hydraulic connections/pressure, bar 2–4 / 200 2–4 / 200 2–4 / 200 2–4 / 200 2–4 / 200
Number/type of hydraulic connection pairs 4-8 / ISO 12.5 4-8 / ISO 12.5 4-8 / ISO 12.5 4-8 / ISO 12.5 4-8 / ISO 12.5
Towing TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm
Lower suspension link axle spacing (alternative spacing), mm 1 010
(920)1 010
(920)1 010
(920)1 010
(920)1 010
(920)
Diameter of the holes in the lower suspension links for the machine suspension pins (alternative Ø) 37,5
(29)37,5
(29)37,5
(29)37,5
(29)37,5
(29)
Axle load, kg 1 960 2 080 2 240 2 730 2 950
Weight, kg 2 360 3 010 3 340 4 025 4 360
K 500 PS K 600 PS K 700 PS K 800 PS K 1000 PS
Working width, mm 5 000 6 000 7 000 8 000 9 850
Transport width, mm 3 000 3 000 3 000 3 000 3 000
Transport height, mm 2 790 3 230 3 830 4 000 4 000
Total length, mm 6 105 6 105 6 105 6 105 6 660
Working depth, mm 0-100 0-100 0–100 0-100 0-100
Arrow tines – AL section, pcs. 23 27 31 35 43
Forged tines – CF section, pcs. 49 59 69 77 91
Arrow tines – AP section, pcs. 23 24 31 32 38
Productivity, ha/hour 3–5 3.5–6 4.5–7 5.5–8 8.5–10
Tractor power, kW/HP 120 / 165 130 / 180 150 / 205 160 / 220 180 / 245
Working speed, km/h 10–14 10–14 10–14 10–14 10–14
Maximum working slope, ° 6 6 6 6 6
Tire measurements - for transportation 19,0/45-17 19,0/45-17 19,0/45-17 19,0/45-17 19,0/45-17
Brakes air / 2 circuits air / 2 circuits air / 2 circuits air / 2 circuits air / 2 circuits
Required pressure, kPa 8,5 8,5 8,5 8,5 8,5
Brake dimensions 300/60 300/60 300/60 300/60 300/90
Hydraulic connections/pressure, bar 2–4 / 200 2–4 / 200 2–4 / 200 2–4 / 200 2–4 / 200
Number/type of hydraulic connection pairs 4-8 / ISO 12.5 4-8 / ISO 12.5 4-8 / ISO 12.5 4-8 / ISO 12.5 4-8 / ISO 12.5
Towing TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm
Lower suspension link axle spacing (alternative spacing), mm 1 010
(920)1 010
(920)1 010
(1 045)1 010
(1 045)1 010
(1 045)
Diameter of the holes in the lower suspension links for the machine suspension pins (alternative Ø) 37,5
(29)37,5
(29)37,5
(50)37,5
(50)37,5
(50)
Axle load, kg 2 730 2 950 3 360 3 620 4 520
Weight, kg 4 025 4 360 4 960 5 345 6 920
K 500 PS LONG K 600 PS LONG K 700 PS LONG K 800 PS LONG K 1000 PS LONG
Working width, mm 5 000 6 000 7 000 8 000 10 000
Transport width, mm 3 000 3 000 3 000 3 000 3 000
Transport height, mm 2 790 3 230 3 830 4 000 4 000
Total length, mm 6 355 6 355 6 355 6 355 6 910
Working depth, mm 0-100 0-100 0–100 0-100 0-100
Arrow tines – AL section, pcs. 23 27 31 35 43
Arrow tines – AL4 section, pcs. 41 47 55 61 75
Forged tines – CF section, pcs. 49 59 69 77 91
Arrow tines – AP section, pcs. 23 24 31 32 38
Productivity, ha/hour 3–5 3.5–6 4.5–7 5.5–8 8.5–10
Tractor power, kW/HP 120 / 165 130 / 180 150 / 205 160 / 220 180 / 245
Working speed, km/h 10–14 10–14 10–14 10–14 10–14
Maximum working slope, ° 6 6 6 6 6
Tire measurements - for transportation 19,0/45-17 19,0/45-17 19,0/45-17 19,0/45-17 19,0/45-17
Brakes air / 2 circuits air / 2 circuits air / 2 circuits air / 2 circuits air / 2 circuits
Required pressure, kPa 8,5 8,5 8,5 8,5 8,5
With brakes/without brakes yes / yes yes / yes yes / yes yes / no yes / no
Brake dimensions 300/60 300/60 300/60 300/60 300/90
Hydraulic connections/pressure, bar 2–4 / 200 2–4 / 200 2–4 / 200 2–4 / 200 2–4 / 200
Number/type of hydraulic connection pairs 4-8 / ISO 12.5 4-8 / ISO 12.5 4-8 / ISO 12.5 4-8 / ISO 12.5 4-8 / ISO 12.5
Towing TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm TPH categories 2 and 3; lower suspension K80; eyelet Ø 40, 50, 70 mm
Lower suspension link axle spacing (alternative spacing), mm 1 010
(920)1 010
(920)1 010
(1 045)1 010
(1 045)1 010
(1 045)
Diameter of the holes in the lower suspension links for the machine suspension pins (alternative Ø) 37,5
(29)37,5
(29)37,5
(50)37,5
(50)37,5
(50)
Axle load, kg 2 810 3 030 3 460 3 720 4 850
Weight, kg 4 125 4 460 5 110 5 495 7 420
FARMETH – the largest manufacturer of agricultural machinery for tillage and sowing in the Czech Republic. The company, founded in 1992, is growing rapidly and devotes much attention and investment to the development of new technologies.
FARMETH agricultural equipment manufactured by this manufacturer must meet the strictest standards of work quality, reliability and durability. All equipment of this manufacturer 36 months warranty provided.
Products and technologies are developed in close collaboration with customers, research institutes and universities. FARMETH The products feature unique technological solutions, some of which are patented. The company seeks not only to improve product quality and create added value, but also to improve production technologies, productivity, and improve occupational safety and environmental protection.
FARMETH The brand is focused on high-quality products and high value. Major investments in modern production management ensure further quality improvement and more efficient production. The goal is to increase the added value of products and strengthen their competitiveness in all markets.
You can rent this equipment!
We offer the possibility of this technique rent for a day, a week or any other time you want. For rental conditions or other land cultivation, sowing, fodder preparation, and fertilization equipment, please contact our technical department.
You may also be interested in:
Kompaktomat NS Germinators
2.5–6-meter mounted seed drills are designed for soil preparation after plowing
Germinators Kompaktomat Max
12.5–15.7-meter mounted cultivators are designed for soil preparation after plowing